 |
 |
 |
 |
 |
|
Data Acquistion Section
|
|
Ethernet, USB & Wireless Section
|
|
 |
 |
 |
 |
|
|
|
|
 New Data Acquistion, Ethernet, USB & Wireless Products
|
|
|
|
|
|
 |
|
|
|
|
 |
|
Wireless Process Transmitter for Sensors with Voltage or Current Output
Click to enlarge the image
|
|
 |
Convert Process Signal to Wireless |
|
Accepts 0 to 1V, 0 to 5V, 0 to 10V and 4 to 20 mA Signals |
|
Industrial NEMA 4X (IP65) Enclosure |
|
Free Software for Monitoring, Recording, and Data Logging Included |
|
Low Power Operation/Sleep Mode for Long Battery Life |
|
UWTC Receivers Work with Up to 48 Wireless Transmitters |
|
|
|
|
|
|
| Last 10 Viewed Products |
[X] |
|
|
|
|
|
|
|
|
|
|
View all of our related products Wireless Transmitters and Receivers
|
|
|
|
The new UWPC wireless process
transmitter converts standard process
signals (0 to 1V, 0 to 5V, 0 to 10V and
4 to 20 mA) into a wireless signal that
can be transmitted up to 120 metres,
eliminating the need for wiring runs in
a variety of environments. The
wireless transmitter is housed in an
IP65 enclosure, providing
water and dust protection. The UWPC
transmits data at preset intervals,
selectable from 2 to 120 seconds.
Transmitted data includes the sensor
reading, along with RF signal
strength and battery status.
The UWPC is compatible with the
UWTC-REC family of wireless
receivers, which can accept signals
from up to 48 wireless transmitters,
and display them on a PC. Receivers
are available with optional display and
analogue output. An analogue output can
be used to interface with a process
controller, PLC or data acquisition
device. Each unit includes free software
that converts your PC into a
monitor, chart recorder or data
logger. Readings can be saved
and later printed or exported to
a spreadsheet file.
Wireless Receivers
UWTC-REC1: 48-channel wireless receiver with USB
UWTC-REC2: 48-channel wireless receiver with USB and single analogue output
UWTC-REC4: 48-channel DIN rail mount wireless receiver with USB and four analogue output signals
UWTC-REC6: economical single channel wireless receiver with single analogue output
SPECIFICATIONS
Input Range: 0 to 1 Vdc, 0 to 5 Vdc, 0 to 10 Vdc or 4 to 20 mA
Accuracy: ±0.04% of range
Input Connection: Panel connector (mating connector supplied)
Computer Interface: USB, for initial transmitter/sensor setup and configuration
Transmit Sample Rate: Programmable from 1 sample/2 sec to 1 sample/120 sec
Radio Frequency (RF) Transceiver Carrier: ISM 2.4 GHz, direct sequence spread spectrum
RF Output Power: 10 dBm (10 mW)
Range of RF Link:
Outdoor Line of Sight: Up to 120 m
Indoor/urban: Up to 40 m
RF Data Packet Standard: IEEE 802.15.4, open communication architecture
Software (Included Free): Requires Windows® 2000, XP or Vista (32 bit) operating system
Power: One 3.6V, lithium "C" cell (included)
Battery Life (Typical): 3 years 1 sample/minute reading rate @ 25°C
Enclosure: NEMA 4 (IP65), polycarbonate
Enclosure Dimensions: 80 L x 82 mm W
Weight: 272 g
|
|
|
To Order |
|
|
Note:
Because of transmission frequency regulations, these products may only be used in the United States, Canada and Europe.
Supplied with measurement/data logging software, lithium "C" cell battery, USB cable, and operator's manual.
|
|
|
|
|
|
|
Related Links
|
|
|
Keywords: Wireless Process Transmitter for Sensors with Voltage or Current Output
|
|
|
|
| |
|
