OMEGA’s PXM6000 Series Pressure Transducer fits easily into your application. This low cost transducer is small and light, and mounting requires no bulky structures. The sensor is a small, about 2.5 mm square, silicon chip with four diffused strain gauges, mounted in the stainless steel case. Laser trimmed resistors provide temperature compensation and adjust zero balance and span. The 30 mV output easily is compatible with most amplifiers and data acquisition systems The PXM6000 uses solid state media isolation for improved reliability. Thin films of chemically inert materials are deposited or grown on the chip surface to provide electrical isolation between the sensor and pressure medium. The sensor is less sensitive to vibration and more dependable in high shock environments because the films add no significant mass. Corrosion resistance is outstanding, and the isolation will remain effective because there is no gel or oil column to deteriorate.
SPECIFICATIONS Excitation: 10 Vdc Regulated Output: 3 mV/V ±10% Input Resistance: 2500 Ω minimum Output Resistance: 1000 to 1500 Ω Zero Balance: 0 mV ±5% FSO Dielectric Isolation Resistance: 100 MΩ Minimum at 45 Vdc Temperature Sensor: Resistance @ 24°C (75°F) 900 to 1500 Ω Temperature Coefficient: 8% to 10%. per 55.6°C(100°F) Accuracy: ± 0.25% FS for all ranges (Linearity, Hysteresis and Repeatability combined ) Operational Temp Range: -54° to 150°C (-65 ° to 300°F) Compensated Temp Range: -54° to 121°C (-65° to +250°F) Thermal Effects: Span: = ± 0.04% of FSO/°C Zero: = ± 0.04% of FSO/°C Vibration Sensitivity: At 35g peak sinusoidal vibration from 10 Hz to 2000 Hz ( 1 /2 " D.A.), the output shall not exceed 0.04% FSO/g for 1 bar range to 0.005% FSO/g for 7 bar and above Natural Frequency: Greater than 35 kHz for 7 bar and above Shock: 100g, 11 milliseconds half sine wave without damage Proof Pressure: 2.0 times rated pressure will not cause changes in performance beyond the specified tolerances Burst Pressure: 3.0 times rated pressure for pressure ranges below 14 bar, or 2.5 times rated pressure for pressure ranges above 14 bar will not cause rupture of the pressure sensor Wetted Parts: 316 Stainless Steel, Silicon Nitride, pyrex glass, epoxy, Kovar Electrical Connection: Style "0" = 0.6 m (2 ft) cable Style "1" = PT1H-10-6P connector Style "6" = micro DIN Connector Pressure Port: G 1/4 Male (std) Optional: G 1/4 Female, G 1/8 Male or Female Weight: 113 g (4 oz.) Mating Connector: Style "1" = PT06F10-6S (not inlcuded) Style "6" Micro DIN mating connector included
For special options consult Sales or Pressure Engineering.
Most Popular models are featured in the "Place Order" below.
For the full selection of all models available, see the "Part Number Builder" below the "Place Order" table.
† All amounts shown in EUR, GBP, or USD
Part Number Builder
Build Your Part Number Below
Pressure Port select from: MA for G 1/8 male MB for G 1/8 female MC for G 1/4 male MD for G 1/4 female
Electrical Connection select from: 0 for 0.6 meter shielded cable 1 for PT1H-10-6P connector or equivalent (mating connector sold separately) 3 for 4 pin solder eyelet(no temp. sensor) 6 for micro DIN connector (mating connector included/no temp sensor)
Pressure Range (Bar) select from: 001 for 0 to 1 Bar 1.60 for 0 to 1.6 Bar 004 for 0 to 4 Bar 006 for 0 to 6 Bar 010 for 0 to 10 Bar 016 for 0 to 16 Bar 025 for 0 to 25 Bar
Pressure Units select from: A for Absolute pressure G for Gauge pressure S for Sealed gauge pressure
Output select from: V for 3 mV/V nominal 5T for 0 to 5 Vdc I for 4 to 20 mA
Note: All combinations may not be valid, check spec sheet for valid part numbers.