Note: These Sensors Require an M12 Extension Cable to Connect the Sensor To Your
Instrumentation. A Partial List Of Our M12 Extension Cables is Included in the Ordering Table Below.
Our RTD sensors with M12 connections provide for easy and efficient installation or removal of these sensors for preriodic calibration, troubleshooting or replacement. Gone
are the days of having to pull extension cables from cable trays in order to calibrate or replace the sensor, now you simply disconnect the sensor from the extension cable
saving cost and downtime. The Series PR-21SL Spring Loaded RTD has been designed to provide our customers with a simple, effective way to adapt our M12 enabled RTD probes for
use in thermowells. To insure the best possible performance, the PR-21SL RTD has a spring loading feature that maintains contact between the probe
and thermowell under static and vibration conditions. This helps to maintain heat transfer between the thermowell and probe, as well as dampening the effect
of vibration on the sensor. With a demonstrated ability to withstand 10gs of vibration between 10 and 500HZ (for 6" long and shorter probes per MIL-STD-202G,
Method 204D, Test Condition A), this probe has shown its ability to withstand real-world conditions.
To select the right length probe for your application, simply measure the depth of the bore in the thermowell (the length from the top of the thermowell to the bottom
of the bore as shown as the “Thermowell Stem Length” in the sketch below).
The PR-21SL sensor assembly is designed to fit into a thermowell with a stem length equal to that specified in the model number. Simply
slide the sensor assembly into the thermowell until bottomed and then compress the spring while making the 1/2NPT connection. Thread sealant tape or
thread compound may be used on the 1/2NPT mounting thread to insure easy removal at a later time. The position of the self-gripping spring can also be
adjusted so that the sensor can be used in a shorter thermowell, simply twist the spring while sliding it along the probe stem until the needed position is reached.
The PR-21SL can also be used as a back-up sensor for a variety of applications. The spring loading feature can be adjusted to fit a variety
of thermowells. The spring loading fitting can be removed altogether and replaced with a compression type fitting if a fixed mounting is needed.
The probe (less spring and hex fitting) can also be used with one of Omega's M12-Handle accessories to turn your spring loaded probe into a hand-held
probe. This flexibility in mounting options, as well as the simplified and robust connection provided by the M12 connector, makes the PR-21SL the perfect solution
for a wide variety of applications.
These RTD sensors can be used in any 2, 3 or 4-wire application by selecting one of the two available wiring
arrangements (see the wiring diagrams below) and using only those wires needed for your connection. This allows for
simplified, trouble free installation with any existing application. This also allows the PR-21 series sensor to be used
for a wide variety of replacement applications since it can be connected as-is with just about any measurement or
control equipment available.
Standard Probe Diameter: 1/4"
Standard Probe Lengths: See Thermowell Stem Lengths in The Order Table Below.
Sensor: Pt100 (100 Ohms at 0°C, .00385 TCR (alpha)) Standard, Pt1000 and Other Options Available.
Accuracy: Class A Standard (per IEC 60751), Others Available Upon Request.
Temperature Range: -50 to 250°C Except for the Connector Which is 85°C Max.
Insulation Resistance: 100 Megohms Minimum at 100VDC at Room Ambient Temperature.
Vibration Resistance: 10gs from 10-500Hz per MIL-STD-202G, Method 204D, Test Condition A.
† All amounts shown in EUR, GBP, or USD Note:
For the alternate wiring arriangement (see Wiring Figure Above), change "-1" at the end of the model number to "-2" at the same price.
For a probe length not listed up to 24", change the stem length in the model number to the required stem length (example: 1250 = 12-1/2") and use the price from the next longer sensor.
Ordering Example: (1) PR-21SL-3-100-A-0600-M12-1 PT100 RTD with M12 Plug Connection, With Spring Loading Fitting to Fit a Thermowell with a Stem Length of 6 Inches (Thermowell not included)., £81.00 plus (1) PR-21SL-3-100-A-1200-M12-1 PT100 RTD with M12 Plug Connection, With Spring Loading Fitting to Fit a Thermowell with a Stem Length of 12 Inches (Thermowell not included)., £86.00, £81.00 + 86.00 = £167.00
Part Number Builder
Build Your Part Number Below
Length select from: -0250 for 2 1/2in. Stem Length -0400 for 4in. Stem Length -0600 for 6in. Stem Length -0900 for 9in. Stem Length -1200 for 12in. Stem Length -1500 for 15in. Stem Length -1800 for 18in. Stem Length -2400 for 24in. Stem Length
Wiring Orientation select from: -1 for Standard Wiring (See Diagram) -2 for Optional Wiring (See Diagram)
Note: All combinations may not be valid, check spec sheet for valid part numbers.